The URL can be used to link to this page

Home My WebLink AboutOrd 4297 04/16/1991 ORDINANCE NO. 4297 AN ORDINANCE AMENDING ARTICLE IV OF CHAPTER 16 (DEVELOPMENT CODE) OF THE VILLAGE CODE OF MOUNT PROSPECT PASSED AND APPROVED BY THE PRESIDENT AND BOARD OF TRUSTEES the 16th day of April , 1991 Published in pamphlet form by authority of the corporate authorities of the Village of Mount Prospect, Illinois, the 22nd day of April , 1991. CB/caf 4/5/91 ORDINANCE NO. 4297 AN ORDINANCE AMENDING ARTICLE IV OF CHAPTER 16 (DEVELOPMENT CODE) OF THE VILLAGE CODE OF MOUNT PROSPECT BE IT ORDAINED BY THE PRESIDENT AND BOARD OF TRUSTEES OF THE VILLAGE OF MOUNT PROSPECT, COOK COUNTY, ILLINOIS: SECTION ONE: That paragraphs D, E, and F of Section 16.407.D entitled "Light Pole Requirements" of chapter 16 (Development Code, as amended, are hereby further amended in their entirety; so that hereinafter said paragraphs D, E and F of Section 15.407 shall be and read as follows: " D. Light Pole Requirements: 1. All poles shall be round tapered seamless poles fabricated from aluminum alloy 6063 - T6. Poles shall be provided with bolt down anchor bases and handholes. Anchor bases and handhole frames shall be manufactured from aluminum alloy 356 - T6. 2. Bracket arms shall be truss tapered elliptical arms manufactured from aluminum alloy 6063 - T6. Bracket arm shall taper to two and three-eighths inches (2-3/8") at luminaire end. 3. Poles shall be designed and fabricated to withstand eight (80) m.p.h, winds and associated wind gusts and vibrations The light poles shall be able to support a luminary panel up to 1.7 square feet. All poles shall be designed in conformance with AASHTO's standard specifications for structural supports for highway and traffic signals. In residential areas, the light standards shall have bolt down bases and shall be constructed of spun aluminum with a twenty five foot (25') mounting height and 10' Truss Arm with wraparound clamp in lieu of Rivnuts. The lighting standards shall be Crouse-Hinds No. RTA8M25AAT10268 Clamp Design, Union Metal Model 154-Y1 Clamp Design, or approved equal. In commercial or business areas, the lighting standards shall have bolt down bases and shall be constructed of spun aluminum with a thirty foot (30') mounting heights. The lighting standard shall be Crouse Hinds No. RTA8M30~kT15268 Clamp Design, Union Metal Model 154Yll Clamp Design or approved equal. In cases where bronze finish is desired, the finish shall be anodized duranotic dark bronze finish on spun aluminum. Painted steel poles shall not be allowed. Alternate poles and mounting height shall be approved by the Director of Public Works. E. Luminaries and Lamps: The luminaries shall consist of a housing, reflector, reflector holder, lamp socket, slipfitter and three (3) terminal photoelectric .cell. The luminaries and lamps shall be high pressure sodium. Any mercury vapor lamps in existence on April 16, 1991 may continue in use. All fixtures components shall be designed to operate under all environmental conditions. All luminaries shall be designed and wired to operate on sixty (60) hertz alternating current with a multiple tap high power factor (95 + % PF) regulator type ballast. All lens shall be heat resistant borosilicate glass. All fixtures shall Chapter 16 Page 2 of 3 be designed to operate at minus twenty degree (-20°F (28°C) minimum starting temperature. 1. The mercury vapor luminaries existing as of April 16, 1991 shall have a die-cast aluminum housing with a removable ballast assembly, acrylic or borosilicate glass refractor, photoelectrical cell receptacle and cell multitap reactor type ballast and universal slipfitter. Acceptable unit include General Electric M-Powr/Door, ITT horizontal luminaire or approved equal. 2. The high pressure sodium luminaire may be either the conventional horizontal flat lens cobra head type or the decorative shoebox type, either of which shall be the cutoff type fixture. 3. The cobra head type shall have die cast aluminum housing, removable ballast assembly, a photoelectrical cell receptacle and cell, a multiple tap reactor type ballast and universal slipfitter receptacle. Acceptable units include: a. For Residential Areas: 1) General Electric M-Powr/Door M2AR15SOH2GMS31 2) Crouse-Hinds OVS15SR22ET or approved equals. b. For commercial Areas: 1) General Electric M-Powr/Door M4AC4OSOA2GMC31 2 ) Crouse-Hinds OVM4OSCW2EF Quad Tap or approved equals. 4. The high pressure sodium decorative shoebox type fixture shall have a formed aluminum housing, removable ballast assembly, a photoelectric cell receptacle and cell, and a multiple tap reactor type ballast. Acceptable units include: a. For Residential Areas: l) General Electric D 25S15SOH2GMC3DBR 2) Quality Lighting ll7-14G150WHPS Quad Tap b. For Commercial Areas: 1) General Electric D40S40SOH2GMC3DBR 2) Quality Lighting ll7-14G-120HPS400PCT F. Wire/Cable Requirements: 1. All wire and cable installed under this Section from the power source to the lighting standards shall be contained in either unit duct manufactured from high density smooth wall polyethylene electrical plastic duct or heavy walled galvanized steel conduit. Direct burial of all wire and cable under this Section prohibited. All wire and cable installed under this Section shall be heat and moisture resistant, Type XHHW, and be suitable for use at seventy five degrees (75°C) (167°F) and shall have insulation rated at 600V. The bare ground wire shall be #SAWG stranded copper wire. hapter 16 Page 3 of 3 2. Ail wire shall be subject to an insulation test to ground after installation. The minimum acceptable resistance to ground shall be two hundred fifty thousand (250,000) ohms. Any section of wiring failing to pass the minimum insulation test for any reason or showing an obvious short circuit shall be rejected. All wire, cable and unitduct to be furnished shall be buried not less than thirty inches (30") below finished grade. 3. All runs shall be continuous without splice in cable or unitduct from pole handhole to pole handhole or to control cabinet. Cable slack shall be provided such that there is a minimum of two feet (2') of slack at the base of all light standards. 4. Adequate slack shall be provided such that the service connection can be made without splices other than at the power source. In the case of aerial service, rigid steel conduit for service pole riser including insulated bushing shall be provided for a service pole riser. 5. When passing under concrete or asphalt surfaces, rigid galvanized steel conduit not less than two inches (2") in diameter with bushings shall be used for raceways. 6. Disconnects shall be provided and installed at all points of connection to the Commonwealth Edison power source. 7. Fuse holders with fuses shall be installed in each conductor and located at the base of each pole so they are accessible through the handhole at the base of the pole. Fuse holders shall be Buss-Tron In- Line Waterproof Fuseholder and Break-a-way Receptacle #HEB-AW-RLC or approved equal. " SECTION TWO: That this Ordinance shall be in full force and effect from and after its passage, approval and publication in pamphlet form in the manner provided by law. AYES: Busse, Corcoran, Floros, Weibel NAYS: None ABSENT: Van Geem, Arthur PASSED and APPROVED this 16th day of April, 1991. -- ~---- ~Gerald L.f Farley ATTEST: Village President Carol A. Fields Village Clerk